- 您现在的位置：买卖IC网 > Sheet目录471 > MAX1385BUTM+ (Maxim Integrated)IC RF LDMOS BIAS CNTRLR 48-TQFN
Dual RF LDMOS Bias Controllers
with I 2 C/SPI Interface
Table 27. Basic Software Initialization
COMMAND
BYTE
0x64
0x64
0x20
0x22
0x24
0x26
0x28
0x2A
0x2C
0x2E
0x30
0x32
0x60
0x74
0x76
0x7A
0x7C
0x52
0x56
DATA
WORD
0x0008
0x0008
0x02A8
0x0EC0
0x02C1
0x0106
0x02A8
0x0EC0
0x02C1
0x0106
0x000F
0x0000
0x0000
0x00CC
0x0066
0x00CC
0x0066
0x01FF
0x01FF
DESCRIPTION
Bring the device out of shutdown mode.
Set internal reference and both DAC channels on.
Set the channel 1 high-temperature threshold to +85°C.
Set the channel 1 low-temperature threshold to -40°C.
Set the channel 1 high-current threshold to 4.3A for 50m ? R SENSE , Av PGA = 2, and V REFADC = 2.5V.
Set the channel 1 low-current threshold to 1.6A for 50m ? R SENSE , Av PGA = 2, and V REFADC = 2.5V.
Set the channel 2 high-temperature threshold to +85°C.
Set the channel 2 low-temperature threshold to -40°C.
Set the channel 2 high-current threshold to 4.3A for 50m ? R SENSE , Av PGA = 2, and V REFADC = 2.5V.
Set the channel 2 low-current threshold to 1.6A for 50m ? R SENSE , Av PGA = 2, and V REFADC = 2.5V.
Set Av PGA1 and Av PGA2 to 2, clock mode to 00 and ADC/DAC references to internal.
Set ALARM, SAFE1, and SAFE2 to depend on nothing (POR).
Set ALARM, SAFE1, and SAFE2 for push-pull/active-high (POR).
Set coarse DAC1 high wiper to 204.
Set coarse DAC1 low wiper to 102 (V GATE = 1.99V for MAX1385, V GATE = 3.98V for MAX1386).
Set coarse DAC2 high wiper to 204.
Set coarse DAC2 low wiper to 102 (V GATE = 1.99V for MAX1385, V GATE = 3.98V for MAX1386).
Set fine DAC1 to midscale.
Set fine DAC2 to midscale.
Table 26. Temperature-Threshold
Settings Examples
Regulating VGS vs. Temperature
The MAX1385/MAX1386 can be used along with a
microcontroller to perform closed-loop regulation of the
TEMPERATURE SETTING
-40°C
-1.625°C
0°C
+27.125°C
+105°C
TWO’S COMPLEMENT
1110 1100 0000
1111 1111 0011
0000 0000 0000
0000 1101 1001
0011 0100 1000
LDMOS FET bias current. For example, software can
read the temperature and use a calibrated look-up
table to determine a new value for the gate drive.
As an example, in noncontinuous conversion mode,
read temperature from remote diode 1 by writing to the
ADCCON register (0x62) with bit D1 set to 1. Wait for
BUSY to go high and then low. Read the ADC result
from the FIFO (0x80). The result bits D15–D12 = 0001
? DACREF × FINECODE + × LOWCODE
2 2
written to the Coarse DAC1/DAC2 Input Low Wiper reg-
ister. The resulting output when the low wiper is higher
than the high wiper is:
V V DACREF
18 8
Basic Software Initialization
The MAX1385/MAX1386 do not power on all internal
blocks when full power is first applied. Software must
write to register 0x64 twice with bit D7 set to 0 during
initialization to enable full operation. A basic initializa-
tion sequence is shown in Table 27.
indicate the measurement source is the external tem-
perature sensor DXP1/DXN1, and bits D11–D3 indicate
two’s-complement temperature in degrees Celsius. Bits
D2, D1, and D0 are temperature subLSBs.
Gate voltage drive range must be previously deter-
mined during initialization by setting the coarse DAC1
high and low limits. Write a new value to FINETHRU1 to
immediately change the output GATE1 between the
high and low wiper limits based on the previous tem-
perature measurement.
The regulation software may also use the alarm thresh-
old limits to determine whether temperature and current
______________________________________________________________________________________
47
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX1470EUI+T
IC RECEIVER 315MHZ 28-TSSOP
MAX1470EVKIT-315
EVAL KIT FOR MAX1470 315MHZ
MAX1471EVKIT-315
EVAL KIT FOR MAX1471 315MHZ
MAX1472EVKIT-433#
EVAL KIT MAX1472
MAX1473EVKIT-433
EVAL KIT MAX1473
MAX1479EVKIT-315
EVAL KIT FOR MAX1479 315MHZ
MAX19700EVKIT
EVAL KIT FOR MAX19700
MAX19985AETX+T
IC MIXER DOWNCONV 36-TQFN-EP
相关代理商/技术参数
MAX1385BUTM+T
功能描述:射频放大器 2Ch RF LDMOS Bias Controller RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel
MAX1385EVC16
功能描述:放大器 IC 开发工具 MAX1385 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V
MAX1385EVKIT+
功能描述:射频开发工具 MAX1385 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MAX1386AETM+
制造商:Maxim Integrated Products 功能描述:
MAX1386CAP+T
制造商:Maxim Integrated Products 功能描述:+-15 KV ESD-PROTECTED, EMC-COMPLIANT, 230KBPS - Tape and Reel
MAX138C/D
功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MAX138CMH
制造商:Maxim Integrated Products 功能描述:44 PINS MQFP PKG - Bulk
MAX138CMH+
制造商:Maxim Integrated Products 功能描述:ADC SGL DUAL SLOPE 3 1/2DIGIT LCD 44MQFP - Rail/Tube